Intel Core 2 Duo Processors: If the alarm sounds, unplug the computer and leave it unplugged until the access panel is replaced. After completing all necessary removal and replacement procedures, run the Diagnostics utility to verify that all components operate properly. Type 2 Battery Holder. On-site service and warranty upgrades are also available.

Uploader: Kajikus
Date Added: 21 February 2009
File Size: 12.61 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 87329
Price: Free* [*Free Regsitration Required]

Disconnect the heatsink control cable hp compaq dx2810 mt the system board and remove the heatsink Heatsink assembly. Type 1 Battery Holder.

Please make a different selection, or visit the product homepage. After removing an expansion card, you must replace it with a new card or expansion slot cover for compaaq cooling of internal components during operation. Match the notch on the module with the tab on the memory socket.

A sharp bend can break the internal wires. Removing an Internal 3. Push down the latch on the side of the hp compaq dx2810 mt drive cage 1then slide the hard drive cage away from the bottom of the chassis 2 as shown below.

Javascript is disabled in this browser. Refer to Installing Additional Drives for an illustration of the retainer screws location.

Make sure the cokpaq disk drive cables are facing the top of the drive cage. No software or drivers are available for this product with the selected cokpaq system. The screws used in the computer are of different thread sizes m lengths; using the wrong screw in an application may damage the unit. While handling a drive, avoid touching the connector. To install an optical drive, refer to Installing an Optical Drive into the 5. Solution and Diagnostic Data Collection.

Last Drivers  BROTHER 9500PC P-TOUCH DRIVER DOWNLOAD

Before you remove the hp compaq dx2810 mt hard drive, be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive. For optimal speed, the channels should be balanced so that the largest amount hp compaq dx2810 mt memory is spread between the two channels.

The system will not operate properly if you install unsupported DIMMs. Cable Fx2810 Always follow good cable management practices when working inside the computer.

Keep all screws with the units removed. If hp compaq dx2810 mt are removing a PCI Express x16 card, pull the retention arm on the back of the expansion socket away from the card and carefully rock the card back and forth until the connectors pull free from the socket.

HP Customer Support – Software and Driver Downloads

This is especially important as the hp compaq dx2810 mt on the hp compaq dx2810 mt are very fragile and any damage to them may require replacing the system board. Intel Core 2 Duo Processors: There is a risk of fire and burns if the battery is not handled properly.

Let HP identify any out-of-date or missing drivers and software How does HP use product data collected with this service? Grasp the cable end of the connector and pull it straight up 2. Raise and rotate the microprocessor retainer to its full open position 2.

Last Drivers  E772P DRIVER

RAM & SSD Upgrades | HP – Compaq dx |

Press the release latch on the chassis base, and then hp compaq dx2810 mt up the rear of the power supply to disengage it from the chassis. Keep these numbers available for use when contacting customer service for assistance. If installing a diskette drive, connect the power and data cables to the rear of the drive and connect the other end of the data cable to the connector on the hp compaq dx2810 mt board labeled FLOPPY.

Reconnect the power cord and any external devices, then turn on the computer. Select an operating system and version to see available software for this product. The system will automatically operate in single channel mode, dual channel mode, or flex mode, depending on how the DIMMs are installed. If you are installing a second hard drive, use four of the extra standard screws that are installed on the interior of the front bezel.

If you are replacing the primary hard drive, use the Recovery Disc Set to restore the operating system, software drivers, and any software applications that were preinstalled on the computer.